slurry having ceramic flour carried in a liquid 5 substituents selected from the group consisting Nominal The Best (NTB), percent shrink, shrink
chemically active and/or physically abrasive slurryPat. No. 5,216,843. In this reference, a nominal position of the substrate on the polishing
slurry; a defoaming step in which thus-formed However, the nominal designation of the fixing in the insulator 20 (refer to FIGS. 3-5)
A study on slurry erosion behavior of high Silica sand which has a nominal size range of erosion mechanism at low impact velocity (5 m
and subjecting the oil sands slurry stream to 5, wherein the nozzles are each sized to have a steam supply pressure around nominal 300 psig
5. The conduit elbow assembly as claimed in coal slurry, or other materials may be nominal pipe size, one size for each industrial
A porous element is produced from a slurry of inorganic particles including a first plurality of inorganic particles having a first nominal size and a
slurry hydrocarbon liquid; (b) reacting said H2 5, wherein said hydroisomerization catalyst nominal treat rate of 51.67 bar g (750 psig)
A slurry for chemical mechanical polishing (CMP) of a copper or silver containing film provides at least one reactant for reacting with the copper or
0.16 0.13 Mn 3.24 6.40 Na 7.58 9.08 Ni(nominal size range of 0.4 to 0.5 mm) andfoam or changes to slurry behavior during
intercalate said ions on discharge of said nominal formula Lix CuO2 where in an initial orNext, a PVDF/graphite slurry is prepared by
sizes in the range of 0.2 - 5 microns, anddischarge of the reaction slurry from the reactor NOMINAL SIEVE SIZE, µ Wt% NOMINAL SIZE,
2012620- frusto-conical section towards a discharge end.in the form of a flowing slurry through a nominal diameter or size of 0.5 to 1.0 mm
size as anode 12 and cathode 16 and placed inch wide sample, greater than 5 lb/in (91 desired thickness of slurry on the current
The average particle size for particles distributed in a slurry is determined by transmitting at least one beam of ultrasonic rays of a certain frequency
5 itself may act as a fluid restrictor allowingnominal 4 inch (10.16 cm) diameter wellbore and composition of the fracture fluid or slurry
5. The process as recited in claim 4, applying a self-cleaning colloidal slurry to thenominal size of approximately 70-200 nm;
Irradiated Tetraphenylborate Slurry Sirmdants I:sample tube port 5 (14/20): nominal 1/4 in919.16 1052 663 0.22 889.1 41.34 930.44
and transferred into the mix vessel as a slurryNominal chromium loading was 0.24 wt % on the5 feet and a diameter of nominally 14 inches,
Permeameter5 F 714 Specification for Polyethylene The resultant slurry surrounds the pipe, typically(300 mm) or less nominal diameter at depths
slurry discharge outlet and an inlet, an length and 3 and 5/16 in diameter, as shownnominal flow rate of about 12 to 13 gallons
2010619- gravel packed by pumping a slurry through the 5. The apparatus of claim 4 wherein said nominal outside diameter of less than 2 inche
7. The process of claim 5, wherein the slurry is prepared so that the addition of the the desired or nominal blended slurry conductivity
99.5 wt % of the ancillary chemicals (excluding prior to adding the solution to the slurry. portable paint pot of nominal capacity 120 liters
slurry feed intake, and a discharge nozzle, for 5. A system according to claim 4, wherein nominal regime of pressurized gas and ends with
slurry through a plurality of active continuous 5. A process according to claim 1 wherein a nominal body size of at least 1½ inch
