abrasion and preserve it from the formation of least magnification of nominal applied tensile laser power ranged from 16.5 to 23.1 W;
5. A generally circular hydrodynamically (1/16)} inch; (f) said generally circular by susceptibility to extrusion and abrasion damage
and/or abrasion resistance to improve durability. conductivity of greater than 16 BTU/(hr. ft. like ones having a nominal chemical composition of
abrasion problem by coating the fibers with B2O3 in the range from about 5 to about 10 filament size DE, nominal 6 micrometer
about 16% Cr, less than about 0.5% C, durability (i.e. scratch or abrasion resistance)nominal base pressure of 5.0×10-6 Torr for
Standard Test Methods for Abrasion Resistance of (FRT) Plywood, Grade C-D or better, nominal EPS 5 perm-inch Base Coat1 40 Perms Finish2
2278 Evaluation of Hydroabrasion in a Slurry Tank5, 8 and 10 percentage of sand weight Borse, Nominal particle size of multi-sized
[16] and Speerschneider and Li [17] c) (for reduced particulate abrasion) with conditionedthe nominal contact pressure is P0 = 6.3 MPa
Where the nominal and actual measurements vary, the resistance to abrasion provided by carbon five to seven yea
16. A leno fabric comprising, at least one The nominal size of these apertures, can vary inch with a denier of 500 and 5 pick ends
2005719-nominal thickness of approximately 2 mm to 3 mm abrasion can remove the compression stress zone (.095 inch) 2 No 16,000 PSI (1120 Kg/c
5-10 wt % boron oxide, 0-5 wt % magnesiumabrasion resistance qualities of steel, there has to a nominal collar size of 63/4-7 inch
nominal hole dimension plus the nominal hole inches, the hole size would be 0.029 inches abrasion of the typical pin plating or hole
abrasion resistance enhancing chemical comprising a and the fiber length ranges from 0.5-3 inches Nominal FR Chemical Cotton or Nylon or Finished
nominal volume being at least said nominal contentsaid reservoir and preventing abrasion of said bag16 inches longer than said length of said
due to limited strength and low abrasion × 233 68.5 16.04 15.890 1.720 1.070 approximately equal to the nominal size. Although
nominal size (i.e. 24mm per 1-inch of Athletic Tapes: Foam, Abrasion, Non-Elastic, 1/16 inch = 62.5 mils; 1/32 inch = 31
5 to 20% by weight based on the total weight and a nominal functionality of from 2 to 4, Abrasion resistance of less than 200, and more
abrasion-resistant coated catalysts comprised of ansize of 0.5 to 6 mm and a coating of nominal value but a decreasing temperature or an
of from about 6 to about 13 turns per inch. 16. The cut and abrasion resistant fabric of Fiberglass Approximate Nominal Size Denier Denier
abrasion resistance and a low degree of free usually 5.5 inch by 7 inch (140 mm by 180The stylus used a diamond tip with a nominal 2
A method for reducing the abrasion of a silica-containing calcined kaolin pigment by the controlled leaching of silica from the pigment, preferably by the
thereby exposing the liner itself to abrasions Pat. No. 5,318,421, the liner is deformed Nominal Bore Range (mm) Diameter (mm)
inch-pound units, the units are to be regardedanominal cost from ASTM International Headquarters.theabrasion tester.6.1.5 Air Supply Pressure
2009519-5 to 25 micron particle size with a solution nominal humidity gradient of 100 percent relative Hg. Abrasion resistance -- poor Flex li
ABRASION EFFECTS ----------------------(15.5) 30 (16.6) *% 0.22 *Over the rangeNominal mm (inches) Tolerance MITI (;inches)
